nails or screws to apply siding

nails or screws for old cedar siding?

if water happens to get in the siding will swell and shrink like a barometer. i would use screws and stainless type, that have a pre-drill head and possible bugle head with seat-cleaning threads these are trim and deck and siding screws. they are expensive. a person can seat these and caulk.

soffit installation

inspect and plan the job in advance. for re-siding applications, nail down any loose panels, boards, or shingles. check surfaces for strhtness and fur when necessary. surfaces should be uniform and strht from various viewing angles. the procedure used to install soffit depends on the construction of the eave.

10 most common install errors with james hardie siding

luckily, it takes lots of water to saturate hardie products its no problem for a contractor to install james hardie products in light rain. 3. hardie plank joints butt joints james hardie siding is 12 feet long, which means that siding on your longer walls will need to join together.

how to install shiplap walls in your home

once each board is in place, put a single nail at every other stud about an inch above the gap in the newly placed board. be sure to nail on the same studs that you nailed the first board to, so that the nail pattern is consistent. we used a single nail on each board, but some prefer to place two nails per board on each stud point.

how to choose nails for hardiplank hunker

hardiplank fiber cement siding can enhance the beauty of any home, but if the installer uses the wrong nails it will ruin the exterior look of your home with potential rust stains especially in humid climates. if a homeowner intends to install his own siding, the importance of using the correct nails can not be expressed enough.

application instructions

apply siding in a manner that prevents moisture intrusion and nail from the center of the siding toward the ends, or from one end to the other end. never nail from the ends of the siding -minimum 8 hot dip galvanized tapered head wood screw, spaced a maximum of 12 inches 305 mm o.c. with 1-1/2 inch

can you screw t1-11 siding? hunker

screws can be used to attach the panels, but the materials cost is greater. screw heads need to be sunk in enough so that they can be covered with a protective compound and painted over, making them disappear. a professional-grade screw gun for decks work well in applying the t1-11 to the studs.

how to install shiplap: 14 steps with pictures

use 2 in 5.1 cm nails or screws to ensure that the nail will pass through the shiplap and deep into the studs. for each method, drive two 2 in 5.1 cm nails or screws strht through the board and into the center of each stud. use the chalk marks that you made earlier as your guide.

how to install shiplap: 14 steps with pictures

nail or screw the shiplap to the wall. you can do this using a hammer, a compressed-air nail gun, or a screw gun. use 2 in 5.1 cm nails or screws to ensure that the nail will pass through the shiplap and deep into the studs. for each method, drive two 2 in 5.1 cm nails or screws strht through the board and into the center of each stud.

why proper nailing is so important for vinyl siding

crooked nails cause siding to buckle. its always important to drive your nails in strht and level on any construction project. however, when youre putting up siding, a nail thats crooked will cause your siding to buckle and sagespecially if you leave room for extra expansion.

how to install vinyl siding

use aluminum, galvanized steel, or other corrosion-resistant nails, staples, or screws when installing vinyl siding. aluminum trim pieces require aluminum or stainless steel fasteners. all fasteners must be able to penetrate a minimum of 1 1/4 32mm into nailable material, such as wood sheathing and framing fig.

dont use drywall screw on exterior siding

dont use drywall screw on exterior siding - new home building tips if you've ever looked at the exterior of the building and noticed that the nails or screws were starting to rust, this video

how to choose nails for hardiplank hunker

pick out stainless steel or hot-dipped galvanized nails size 6d, 1 1/2-inch-long siding nails and 2-inch long siding nails in the quantity you need for your project. if the hardiplank is being installed on a building in a humid climate or near the ocean or any large body of water, the stainless steel nails are the first choice.

how do you fasten cement board siding??

re: how do you fasten cement board siding?? been a while since i have done either a roof or a siding job but the last time i did siding we used roofing nailer. however, i recall doing roofs that the roofing nailer had a gauge that you used to line up on the bottom of the shingle to get the proper placement of the nail.

fastening tips for hardieplank lap siding technical

nails are recommended for pin-backs. headed siding nails are allowed. place pin-backs no closer than 1 in. from plank ends and 3/4 in. from plank edge into min. 3/8 in. wood structural panel. pin-backs are not a substitute for blind or face nailing. the nail shall be nailed flush to the surface not countersunk , and

how to nail vinyl siding correctly

vinyl siding tends to expand and contract considerably with temperature changes. for this reason, manufacturers design it to hang loosely on the nails rather than to be tightly nailed like wood siding. the problem should be easy to diagnose. simply go outside, grab the lower edges of a siding course and try to slide it back and forth photo 1 .

hardiplank installation instructions

hd x 1 1/4 long screws must penetrate 1/4 or 3 threads into metal framing. for face nail application of 9 1/2 wide or less siding to osb, fasteners are spaced a maximum of 12 o.c. ** the use of a siding nail or roofing nail may not be applicable to all installations where greater windloads or higher exposure categories of wind

how to nail vinyl siding correctly

vinyl siding will pop and crackle with every change of sunlight and temperature if nailed incorrectly. here's how to fix the problem if you have it, and how to nail or renail siding so that it moves freely and silently for the life of your house. each piece of siding should move back and forth at

why screws are better than nails for vinyl installation

nails are generally made of steel that can rust and corrode causing loss of integrity and staining of the installed product. screws used for vinyl can be corrosion proof stainless steel or another corrosion proof material. a few of the vinyl fasteners that are recommended are also the same as those used for aluminum siding.

how to install log siding doityourself.com

with the hammer or nail gun, nail each side of the log siding making sure the nails are 45 degrees under the tongue. doing this will hide the nail when you install the next log. repeat these steps for all the logs until you reach the top of the wall. step 5. check for level. every few rows of logs you install check to make sure they are level.

cedar siding: nails or screws?

siding has been nailed for years on plenty of houses that are 100 years old. the nails need to hit something solid more often than not. try using ring shank nails aka shake and shingle nails . you can get them in different sizes. get some long enough to go through your siding and the underlayment, and make sure most of them go into studs if possible.

siding nails

stainless steel offers the ultimate protection against corrosion. cedar and fiber cement siding should be fastened with stainless steel fasteners. always check the installation guide and fasten per the recommendations. install long siding with a fastener of equal durability. eliminate unsightly black streaks on cedar siding and fences by fastening

fastening tips for hardieplank lap siding technical

james hardie prefers and recommends installation of hardieplank lap siding by the blind nailing technique, such that fasteners are hidden by the course above. fasteners shall be installed between 1 in. and 3/4 in. from the top edge and no closer than 3/8 in. from the ends of the plank.

what type of screws or nails are used to fasten the log

for exterior quarter log siding we recommend the use of galvanized siding nails 8 penny ring shank or corrosion resistant decking screws 2 2.5 long . for exterior half log siding we recommend the use of corrosion resistant decking screws 2.5 3 long or galvanized siding nails 14 penny ring shank . for interior products

how to install stone-veneer siding panels

drive screws through the holes in the nail flange; drive nails directly through the flange. drive the fasteners into framing whenever possible. full-size panels require four fasteners, at least two into framing. end fasteners must be within 3 in. of the end of the panel, and at least 1/2 in. from the edge.

the correct nails for installing vinyl windows ehow

vinyl window framework and siding are often installed as one project, and both use the same types of nails and attachments to keep them in place. nailing down vinyl frames is not like installing other types of siding. if you tried to treat vinyl like you treat wood installation projects, the vinyl can fail over time.

proper screws for vinyl siding

use roofing nails. if you gotta screw it use 1 5/8 construction screws. longer if need be. the problem with screws is the heads are not big enough. sometimes the siding will pop loose because the head of the screw pulled through. plus if your screws are not set right they will telegraph through to the next piece of siding. with a nail you can beat it in.